Recently,
Tim Semic, our Support Manager, suggested we create a blog on “how not to kill your inkjet label
printer”. I thought immediately, “that’s
a great idea”. Tim suggested the
questions; and we both worked on the answers.
This post features answers based on our work with Epson label
printers primarily; but the concept applies to label printers based on Memjet and HP as
well.
OK, I don’t want
to kill my label printer, tell me more.
The most common hardware problem with inkjet label printers are
clogged nozzles. An inkjet printhead has thousands of very tiny nozzles. Memjet
claims to have 70,400 nozzles in an 8.77” printhead: https://www.memjet.com/versapass/. These nozzles are all subject to clogging;
and thus, ruining your day.
What causes print
nozzles to clog?
The number one reason inkjet nozzles clog
is particles carried into the printer on the label media. As this foreign material enters the printhead,
nozzles can get plugged. The second
reason for clogged nozzles is similar to the first; dust and other foreign
material in the air may plug inkjet nozzles as well. The third way inkjet nozzles will clog occurs
when the ink inside of the printhead dries. Dried ink inside the printhead may
occur when leaving the printer powered off for long periods of time, and/or
when the printer is kept in very dry environmental conditions.
What are the
symptoms of clogged print nozzles?
A plugged nozzle symptom will manifest as
white lines running across the label print output in the orientation of the
printhead. These white lines are a classic symptom of clogged print
nozzles. The lines that you see are actually the white label where no ink
was applied. The other tell-tail symptom of clogged print nozzles is
when your printer constantly goes into maintenance mode.
 |
The thin lines
you see are from the label showing through due to clogged print nozzles.
|
My
printer occasionally makes noise when idle and pauses often
during printing. Epson Label Printers with an LCD display will
show “maintenance" or "head maintenance".
Your label printer has
a service called Head Maintenance that runs periodically to keep the
ink jet nozzles clear, and to prevent them from drying out. This maintenance
service works by forcing a small amount of ink through the printer’s nozzles.
However, this service may run repeatedly when clogged nozzles are
detected.
 |
| Head Maintenance |
In the
C7500, one option is to turn on the “spitting function”; also called
“Continuous Printing”.
 |
| C7500 Continuous Printing |
With this
setting, the printer “spits” out very small quantities of ink, invisible to the
naked eye, randomly throughout the print. Memjet printers have the same functionality. Sometimes the label may appear slightly grey from the ink, even though
you can’t see the individual drops without a magnifying glass. We recommend this setting if the tiny ink
spots are OK with your print output.
The other
option is “pause” for maintenance. In
this situation, the printer stops occasionally to check the printhead.
On the
C3500, you can turn off the checking/cleaning function of the printer to save
ink and to reduce the number of maintenance kits required. As we print very few labels, we typically run
our C3500 with the “no missing dot detection mode” selected; and then clean
manually when needed.
What can I do if
my printer is in a clogged nozzle condition?
Performing a manual cleaning is a way to
take control of removing clogs in the nozzles. Prior to performing a manual
cleaning, it’s best practice to print a nozzle check pattern from the printer
utility software. A nozzle check pattern will provide you a baseline view of
the problem. The nozzle check pattern prints lines of every CMYK color and will
reveal areas and the color(s) that are being affected by the clogged nozzles.
 |
| Nozzle check pattern |
If you see gaps in the nozzle check
pattern, the next step is to run a manual cleaning on the printer. After the
cleaning cycle completes, you may want print out another nozzle check pattern to
look for improvement. You should repeat the cleaning/test pattern cycle
until either the clogged nozzles have been cleared, or you no longer see
improvement occurring.
The manual cleaning didn’t completely resolve the issue. Now what?
Once you determine that the cleaning
utility is unable to resolve the clogged nozzle condition, the printer
will have to be repaired by the manufacturer in the case of Epson or any other
manufacturer with permanent printheads.
For Memjet printers, you can also attempt to rehydrate the ink by
placing the printhead in the shipping cap with distilled water. If the nozzles remained plugged, you’ll need to
replace the printhead.
How can clogged
print nozzles be prevented in the first place?
The number one way to prevent nozzle
plugging is to keep your label media in the plastic bags in which they
shipped. Keeping your labels in the bags
reduces the likelihood of foreign material from entering the printer.
In addition, you should keep the work
area with the printer relatively dust free.
Don’t run an inkjet printer in a dusty environment.
Also, it’s recommended that you keep the
printer powered on at all times once you are printing regularly. For example, Memjet recommends their printers
run 24/7. Also, don’t leave your printer
powered off for a long period of time. Once powered off, the printer can no
longer keep the nozzles from drying out.
When left powered on, the printer will
not consume much electricity since as it switches into an Energy Saving Mode.
While in energy saving mode, the printer will still perform a limited
number of maintenance routines.
Should I worry about “Dry Climates??
Whether hot
or cold, dry climates will cause the ink in the print nozzles to dry at an
increased rate. In conditions of low humidity below 20%, a humidifier may be
placed near your printer, with the goal of keeping the proximate humidity above
20%. Here are the general printer
climate specifications:
|
Temperature
|
Operating: 5 to
35°C {41 to 95°F} Storage: -20 to 40°C {-4 to 104°F} (At
40°C {104°F}: up to 1 month)
|
|
Humidity
|
Operating: 20
to 80% RH.
Storage: 5 to 85%RH (No condensation)
|
With thousands of inkjet label printers sold and installed, we find these devices as the best current option; and we want to keep them working for you. We hope you find these recommendations of
value. If you follow the above recommendations, you fewer problems, and
have more uptime on your inkjet label printer.
Happy Printing!
Tim Semic/Guy Mikel
855-962-7670
